Logo

ASTM F2648/F2648M-13

Historical Revision

Standard Specification for 50 mm to 1500 mm [2 in. to 60 in.] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications

$83.00

$83.00

$149.40


Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


Stay effortlessly up-to-date with the latest standard revisions. When new versions are released, they're automatically charged and delivered to you, ensuring seamless compliance.

...

1.1 This specification covers requirements and test methods for annular corrugated profile wall polyethylene pipe and fittings with an interior liner. The inside diameters covered are 2 to 60 in. [50 to 1500 mm].

1.2 The requirements of this specification are intended to provide non-pressure (gravity flow) pipe and fittings suitable for underground use for subsurface and land drainage systems, which do not operate under surcharge pressure heads.

Note 1Pipe and fittings produced in accordance with this specification are be installed in compliance with Practice D2321 or Practice F449 based on diameter limitations within the respective standards.
Note 2Subsurface and land drainage systems pertain principally to non-municipal or private facilities for water table control, storm drainage and agricultural drainage applications. The products supplied under this specification are not intended for any sanitary sewer or municipal storm sewer applications.

1.3 This specification covers pipe and fittings with an interior liner using an annular exterior corrugated profile (Fig. 1).

Annular Corrugated Profile Wall Polyethylene Pipe with
 Interior Liner
FIG. 1 Annular Corrugated Profile Wall Polyethylene Pipe with Interior Liner
TABLE 1 Pipe Stiffness and Pipe Dimensions

Pipe Inside DiameterA

Minimum Pipe Stiffness at 5% Deflection

Minimum Inner Liner Thickness

inch

[mm]

lb/in/in

[kPa]

Inch

[mm]

2

[50]

50

[345]

0.020

[0.5]

3

[75]

50

[345]

0.020

[0.5]

4

[100]

50

[345]

0.020

[0.5]

6

[150]

50

[345]

0.020

[0.5]

8

[200]

50

[345]

0.024

[0.6]

10

[250]

50

[345]

0.024

[0.6]

12

[300]

50

[345]

0.035

[0.9]

15

[375]

42

[290]

0.040

[1.0]

18

[450]

40

[275]

0.051

[1.3]

21

[525]

38

[260]

0.060

[1.5]

24

[600]

34

[235]

0.060

[1.5]

27

[675]

30

[205]

0.060

[1.5]

30

[750]

28

[195]

0.060

[1.5]

36

[900]

22

[150]

0.067

[1.7]

42

[1050]

20

[140]

0.071

[1.8]

48

[1200]

18

[125]

0.071

[1.8]

54

[1350]

16

[110]

0.079

[2.0]

60

[1500]

14

[97]

0.079

[2.0]

A Inside Diameters for metric (SI) sizes are in direct Imperial equivalent dimensions

1.4 This specification permits the use of recycled materials for pipe in accordance with the requirements in Section 5.

1.5 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents: therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


This specification covers the general requirements and corresponding test methods for non-pressure (gravity flow) polyethylene (PE) pipes and fittings having interior liner with annular corrugated exterior wall profile, and whose inside diameters are 2 to 60 in. [50 to 1500 mm]. These pipes and fittings are suitable for underground use in subsurface and land drainage systems, which do not operate under surcharge pressure heads. Material requirements are specified for pipe and blow molded fittings, rotationally molded fittings and couplings, injection molded fittings and couplings, and rework materials. The resulting products shall be tested as appropriate, and shall conform to specified requirements for workmanship, dimension (inside diameter, length, minimum inner liner thickness, and perforations), stiffness, flattening resistance, impact resistance, and slow crack growth resistance of PE plastics without pigment.


SDO ASTM: ASTM International
Document Number F2648
Publication Date Jan. 1, 2013
Language en - English
Page Count 8
Revision Level 13
Supercedes
Committee F17.65
Publish Date Document Id Type View
May 1, 2023 F2648_F2648M-23 Revision
March 1, 2022 F2648_F2648M-22 Revision
Feb. 1, 2020 F2648_F2648M-20 Revision
Dec. 1, 2017 F2648_F2648M-17 Revision
Jan. 1, 2013 F2648_F2648M-13 Revision
Aug. 1, 2011 F2648_F2648M-11 Revision
Dec. 1, 2010 F2648_F2648M-10 Revision
May 15, 2007 F2648_F2648M-07 Revision