Logo

ASTM F2623-24e1

Current Revision

Standard Specification for Polyethylene of Raised Temperature (PE-RT) Systems for Non-Potable Water Applications

$76.00

$76.00

$136.80


Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


Stay effortlessly up-to-date with the latest standard revisions. When new versions are released, they're automatically charged and delivered to you, ensuring seamless compliance.

...

1.1 This specification establishes requirements for polyethylene of raised temperature (PE-RT) systems for non-potable water applications. System components include PE-RT SDR 9 tubing, manifolds, fittings, valves and other appurtenances, and mechanical and fusion joining. PE-RT tubing is pressure rated for water at 73 °F (23 °C) and 180 °F (82 °C), and optionally 140 °F (60 °C). Included are requirements for materials, workmanship, dimensions and tolerances, product tests, and markings, and an optional barrier layer. Fittings include mechanical insert fittings and fusion fittings.

1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3.1 Values in parentheses are appropriately rounded for accuracy and precision and are not exact equivalents.

1.4 The tubing systems produced under this specification are intended for use in the transport of non-potable water such as hydronic and irrigation systems.

1.4.1 PE-RT tubing containing an outside surface or mid-wall gas barrier layer or both is acceptable.

1.4.2 PE-RT systems under this standard are not intended for use in the transport of potable water. See Specification F2769 for PE-RT potable water distribution systems.

1.5 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


This specification establishes the basic requirements and corresponding test methods for polyethylene of raised temperature (PE-RT) SDR 9 tubing that is outside diameter controlled, and pressure rated for water at specific temperatures. The tubing produced under this specification shall be permitted for use in general fluid transport, including hydronics and irrigations systems. The plastic used to make the tubing shall be virgin plastic or reworked plastic and shall have Plastics Pipe Institute (PPI) long-term hydrostatic design stress and pressure ratings as the specified temperatures. When evaluated by the test procedures provided herein, the tubing shall meet specified requirements for workmanship, dimensions such as outside diameter and wall thickness, sustained pressure, burst pressure, oxidative resistance, and bent tubes. Quality assurance and product marking methods are also considered.


SDO ASTM: ASTM International
Document Number F2623
Publication Date Feb. 1, 2024
Language en - English
Page Count 12
Revision Level 24e1
Supercedes
Committee F17.26
Publish Date Document Id Type View
Feb. 1, 2024 F2623-24E01 Revision
Feb. 1, 2024 F2623-24 Revision
Dec. 1, 2023 F2623-23 Revision
Feb. 1, 2022 F2623-22 Revision
April 15, 2019 F2623-19 Revision
Dec. 15, 2014 F2623-14 Revision
March 1, 2008 F2623-08 Revision
Feb. 1, 2007 F2623-07 Revision