Logo

ASTM F2159-14

Historical Revision

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps for SDR9 Crosslinked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

$83.00

$83.00

$149.40


Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


Stay effortlessly up-to-date with the latest standard revisions. When new versions are released, they're automatically charged and delivered to you, ensuring seamless compliance.

...

1.1 This specification establishes requirements for sulfone plastic insert fittings and copper crimp rings for four sizes (3/8 , 1/2 , and 3/4 and 1) of cross-linked polyethylene (PEX) tubing that meet the requirements for Specification F876 and polyethylene of raised temperature (PE-RT) tubing that meet the requirements of Specifications F2623 and F2769. These fittings are intended for use in 100 psi (690 kPa) cold- and hot-water distribution systems operating at temperatures up to and including 180°F (82°C). Included are the requirements for material, molded part properties, performance, workmanship, dimensions, and markings to be used on the fittings and rings.

1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 The following is an index of the appendix in this specification:

GO/NO-GO Crimp Gauges

Appendix X1

1.4 The following precautionary caveat pertains only to the test method portions, Sections 11 and 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.


This specification establishes requirements for sulfone plastic insert fittings utilizing a copper crimp ring for SDR9 cross-linked polyethylene (PEX) tubing for cold- and hot-water distribution systems. Material for fitting shall be molded from sulfone plastic. Molded part shall not crack, split, or shatter and be free of visible splay. Fittings shall be tested for performance requirements such as hydrostatic burst, hydrostatic sustained pressure strength, thermocycling, excessive temperature-pressure capability, dimensions, workmanship, finish, appearance, assembly, crimp joint, and insert crush test.


SDO ASTM: ASTM International
Document Number F2159
Publication Date Aug. 1, 2014
Language en - English
Page Count 7
Revision Level 14
Supercedes
Committee F17.10
Publish Date Document Id Type View
March 1, 2023 F2159-23A Revision
Feb. 1, 2023 F2159-23 Revision
May 1, 2021 F2159-21 Revision
Nov. 1, 2020 F2159-20 Revision
Aug. 1, 2019 F2159-19A Revision
April 1, 2019 F2159-19 Revision
Nov. 1, 2018 F2159-18A Revision
April 1, 2018 F2159-18 Revision
Aug. 1, 2014 F2159-14 Revision
April 15, 2011 F2159-11 Revision
Feb. 1, 2010 F2159-10 Revision
Dec. 1, 2009 F2159-09 Revision
May 1, 2005 F2159-05 Revision
May 10, 2003 F2159-03E01 Revision
May 10, 2003 F2159-03 Revision
May 10, 2002 F2159-02 Revision
Dec. 10, 2001 F2159-01 Revision