Logo

ASTM F1959/F1959M-24b

Current Revision

Standard Test Method for Determining the Arc Rating of Materials for Clothing

$76.00

$76.00

$136.80

$91.00

$91.00

$163.80



Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


Stay effortlessly up-to-date with the latest standard revisions. When new versions are released, they're automatically charged and delivered to you, ensuring seamless compliance.

Document Preview Not Available...

1.1 This test method is used to determine the arc rating of materials intended for use as flame resistant clothing for workers exposed to electric arcs that would generate heat flux rates of approximately 2100 kW/m2 [50 cal/cm2s] using an open air arc.

1.2 This test method will determine the arc rating of materials which meet the following requirements: less than 150 mm [6 in.] char length and less than 2 s afterflame when tested in accordance with Test Method D6413.

1.2.1 It is not the intent of this test method to evaluate non flame-resistant materials.

1.3 The materials used in this test method are in the form of flat specimens.

1.4 This test method shall be used to measure and describe the properties of materials, products, or assemblies in response to convective and radiant energy generated by an electric arc under controlled laboratory conditions.

1.5 The values stated in SI units shall be regarded as standard except as noted. Within the text, alternate units are shown in brackets. The values stated in each system may not be exact equivalents therefore alternate systems must be used independently of the other. Combining values from the systems described in the text may result in nonconformance with the method.

1.6 This test method does not apply to electrical contact or electrical shock hazards.

1.7 This standard shall not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.

1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautions, see Section 7.

1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


5.1 This test method is intended for the determination of the arc rating of a material, or a combination of materials.

5.1.1 Because of the variability of the arc exposure, different heat transmission values may be observed at individual sensors. Evaluate the results of each sensor in accordance with Section 12.

5.2 This test method maintains the specimen in a static, vertical position and does not involve movement except that resulting from the exposure.

5.3 This test method specifies a standard set of arc exposures performed under controlled laboratory conditions. Different exposure conditions have the potential to produce different results. In addition to the standard set of exposure conditions, other conditions representative of the expected hazard may be used and shall be documented in the reporting of the testing results.

SDO ASTM: ASTM International
Document Number F1959
Publication Date July 1, 2024
Language en - English
Page Count 18
Revision Level 24b
Supercedes
Committee F18.65
Publish Date Document Id Type View
July 1, 2024 F1959_F1959M-24B Revision
March 1, 2024 F1959_F1959M-24A Revision
Jan. 1, 2024 F1959_F1959M-24 Revision
Dec. 1, 2023 F1959_F1959M-23A Revision
Oct. 1, 2023 F1959_F1959M-23 Revision
Dec. 1, 2022 F1959_F1959M-22 Revision
April 1, 2014 F1959_F1959M-14E01 Revision
April 1, 2014 F1959_F1959M-14 Revision
Oct. 1, 2013 F1959_F1959M-13 Revision
Oct. 1, 2012 F1959_F1959M-12 Revision
Nov. 15, 2006 F1959_F1959M-06AE01 Revision
Nov. 15, 2006 F1959_F1959M-06A Revision
Nov. 1, 2006 F1959_F1959M-06 Revision
Dec. 15, 2005 F1959_F1959M-05A Revision
Nov. 1, 2005 F1959_F1959M-05 Revision
Nov. 1, 2004 F1959_F1959M-04 Revision
April 10, 1999 F1959_F1959M-99 Revision