Logo

ASTM D4868-17

Current Revision

Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels

$61.00

$61.00

$109.80

$73.00

$73.00

$131.40



Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


Stay effortlessly up-to-date with the latest standard revisions. When new versions are released, they're automatically charged and delivered to you, ensuring seamless compliance.

...

1.1 This test method covers the estimation of the gross and net heat of combustion in SI units, megajoules per kilogram, of hydrocarbon fuels and blendstocks from the fuel density and sulfur, water, and ash contents.

1.1.1 This test method is not applicable to fuels containing non-hydrocarbons such as alcohols (for example, ethanol, methanol), ethers (for example, MTBE), or esters (for example, biodiesel).

Note 1: The equation for estimation of net and gross heat of combustion used in this method was originally published as NBS Miscellaneous Publication No. 97.

1.2 This test method is especially useful for estimating, using a minimum number of tests, the heat of combustion of burner and diesel fuels (which do not contain non-hydrocarbon components) for which it is not usually critical to obtain very precise heat determinations.

Note 2: More accurate estimation methods are available for aviation fuels (Test Methods D1405, D4529,and D3338). However, those estimation methods require additional tests to those required in this test method.

1.3 This test method is purely empirical (Note 1). It was derived using liquid hydrocarbon fuels produced by normal refining processes from conventional crude oil that conform to the requirements of specifications for petroleum fuels as described in Note 3. This test method is valid for those fuels in the density range from 750 kg/m3 to 1000 kg/m3 and those that do not contain an unusually high aromatic content. High aromatic content fuels will not normally meet some fuel specification criteria.

Note 3: The estimation of the heat of combustion of a hydrocarbon fuel from its density and sulfur, water, and ash content is justifiable only when the fuel belongs to well-defined classes for which a relationship between these quantities have been derived from accurate experimental measurements on representative samples of these classes. Even in these classes, the possibility that the estimate can be in error for individual fuels should be recognized. This test method has been tested for a limited number of fuels from oil sand bitumen and shale oil origin and has been found to be valid. The classes of fuels used to establish the correlation presented in this test method are represented by the following applications:

Fuel (not applicable to any fuels containing non-hydrocarbon components)

Specification

Fuel Oils

 

Grades No. 1, 2, 4 (light), 4, 5 (light), 5 (heavy), and 6

D396

Diesel

 

Grades No. 1-D, 2-D, and 4-D

D975

Aviation Turbine

 

Jet A and Jet A-1

D1655

Jet B

D6615

Gas Turbine

 

Grades No. 0-GT, 1-GT, 2-GT, 3-GT, and 4-GT

D2880

Kerosene

 

Grades No. 1-K and 2-K

D3699

1.4 This test method is not applicable to pure hydrocarbon compounds. It is not intended as a substitute for highly accurate experimental measurements of heat of combustion (Note 4).

Note 4: The procedures for the experimental determination of the gross and net heats of combustion are described in Test Methods D240 and D4809.

1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


4.1 This test method is intended for use in cases where an experimental determination of heat of combustion is not available and cannot be made conveniently, and where an estimate is considered satisfactory. It is not intended as a substitute for experimental measurement of heat of combustion.

SDO ASTM: ASTM International
Document Number D4868
Publication Date Jan. 1, 2017
Language en - English
Page Count 3
Revision Level 17
Supercedes
Committee D02.05
Publish Date Document Id Type View
Jan. 1, 2017 D4868-17 Revision
Dec. 10, 2000 D4868-90R95E01 Revision
Dec. 10, 2000 D4868-00 Revision
May 1, 2010 D4868-00R10 Reaffirmation
May 1, 2005 D4868-00R05 Reaffirmation