Logo

ASTM D3035-22

Current Revision

Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter

$69.00

$69.00

$124.20

$83.00

$83.00

$149.40



Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


Stay effortlessly up-to-date with the latest standard revisions. When new versions are released, they're automatically charged and delivered to you, ensuring seamless compliance.

...

1.1 This specification covers polyethylene (PE) pipe made in thermoplastic pipe dimension ratios based on outside diameter IPS 1/2 to 3, for both non-pressure and pressure rated water (see Appendix X1). Included are requirements for polyethylene compounds and PE plastic pipe, a system of nomenclature for PE plastic pipe, and requirements and test methods for materials, workmanship, dimensions, sustained pressure, and burst pressure. Methods of marking are also given.

Note 1: Significant changes have been made to this specification to remedy duplication of sizes with other specifications, for DIPS sizes and larger sizes refer to the appropriate standard specification such as Specification F714 or AWWA C906.

1.2 For pipes produced under this specification that are intended for use in the distribution and transmission of potable water without oxidizing disinfectants, potable and non-potable water, grey water, reclaimed water, wastewater, force main and gravity municipal sewage, etc, the user should consult the manufacturer to determine whether the fluid being transported is compatible with polyethylene pipe and will not affect the service life beyond limits acceptable to the user.

1.3 For pipes produced under this specification that are intended for use in the distribution and transmission of potable water or other fluids containing oxidizing disinfectants (for example, Hypochlorous acid or chloramines), special requirements for PE compounds are specified in 5.2 and 5.3, and DR limitations are specified in 6.2.1.1 and 6.2.2.1.

Note 2: Refer to specification AWWA C901 for other suitable potable water options.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


This specification covers polyethylene (PE) pipes made in thermoplastic pipe dimension ratios based on outside diameter, and pressure rated for water. All pipes produced under this specification may be used for the transport of water, industrial process liquids, effluents, slurries, municipal sewage, etc. Included are criteria for classifying PE plastic pipe materials and PE plastic pipe, and a system of nomenclature for PE plastic pipe. PE pipes shall be evaluated by the test procedures given herein, and shall conform to specified requirements for workmanship, dimensions, sustained pressure at ambient and elevated temperatures, hydrostatic burst pressure, tensile strength at yield, and environmental stress cracking.


SDO ASTM: ASTM International
Document Number D3035
Publication Date Nov. 1, 2022
Language en - English
Page Count 8
Revision Level 22
Supercedes
Committee F17.26
Publish Date Document Id Type View
Nov. 1, 2022 D3035-22 Revision
Aug. 1, 2021 D3035-21 Revision
March 1, 2015 D3035-15 Revision
Aug. 1, 2014 D3035-14A Revision
March 1, 2014 D3035-14 Revision
July 1, 2012 D3035-12E02 Revision
July 1, 2012 D3035-12E01 Revision
July 1, 2012 D3035-12 Revision
Dec. 1, 2010 D3035-10 Revision
March 1, 2008 D3035-08 Revision
Dec. 15, 2006 D3035-06 Revision
Dec. 1, 2003 D3035-03A Revision
Sept. 10, 2003 D3035-03 Revision
Aug. 10, 2001 D3035-95 Revision
Aug. 10, 2001 D3035-01 Revision