Logo

ASTM D2513-18

Historical Revision

Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings

$91.00

$91.00

$163.80


Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


Stay effortlessly up-to-date with the latest standard revisions. When new versions are released, they're automatically charged and delivered to you, ensuring seamless compliance.

Document Preview Not Available...

1.1 This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and rapid crack resistance of polyethylene pipe, tubing, and fittings for use in fuel gas pipelines for direct burial and reliner applications. The pipe and fittings covered by this specification are intended for use in the transmission and distribution of natural gas. Requirements for the qualifying of polyethylene systems for use with liquefied petroleum gas are also covered.

1.1.1 This specification does not cover threaded pipe. Design considerations are discussed in Appendix X1. In-plant quality control programs are specified in Annex A1 and Annex A2.

1.1.2 See Specification F2619/F2619M for polyethylene piping for pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water.

1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 The following is an index of the annexes and appendix in this specification:

Annex

Subject

Annex A1

In-Plant Quality Control for all materials up to 12 in.

Annex A2

In-Plant Quality Control for PE materials 14 in. and larger.

 

 

Appendixes

Subject

Appendix X1

Design Consideration

1.5 The following precautionary caveat pertains only to the test method portion, Section 6, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


This specification covers the requirements and test methods for material, dimensions, hydrostatic burst strength, tensile strength, chemical resistance, sustained pressure, heat fusion, and impact resistance of plastic pipes, tubing, and fittings used for direct burial and reliner applications in fuel gas mains and services for the distribution of natural gas. This specification does not cover threaded pipe. The plastic used to make the pipes and fittings shall be virgin plastic or reworked plastic having Plastics Pipe Institute (PPI) long-term hydrostatic design stress and hydrostatic design basis rating.


SDO ASTM: ASTM International
Document Number D2513
Publication Date April 15, 2018
Language en - English
Page Count 17
Revision Level 18
Supercedes
Committee F17.60
Publish Date Document Id Type View
July 1, 2024 D2513-24 Revision
Dec. 1, 2020 D2513-20 Revision
Aug. 1, 2019 D2513-19 Revision
Aug. 1, 2018 D2513-18A Revision
April 15, 2018 D2513-18 Revision
Dec. 15, 2016 D2513-16A Revision
Dec. 1, 2016 D2513-16 Revision
April 25, 2014 D2513-14E01 Revision
April 25, 2014 D2513-14 Revision
Feb. 1, 2013 D2513-13 Revision
April 1, 2012 D2513-12AE01 Revision
April 1, 2012 D2513-12A Revision
Feb. 1, 2012 D2513-12 Revision
Dec. 1, 2011 D2513-11C Revision
Nov. 1, 2011 D2513-11B Revision
Aug. 1, 2011 D2513-11A Revision
Feb. 1, 2011 D2513-11E01 Revision
Feb. 1, 2011 D2513-11 Revision
Dec. 1, 2009 D2513-09A Revision
May 1, 2009 D2513-09 Revision
Nov. 1, 2008 D2513-08B Revision
July 1, 2008 D2513-08A Revision
May 1, 2008 D2513-08 Revision
Nov. 15, 2007 D2513-07BE01 Revision
Nov. 15, 2007 D2513-07B Revision
May 1, 2007 D2513-07A Revision
March 1, 2007 D2513-07 Revision
Nov. 1, 2006 D2513-06B Revision
Aug. 15, 2006 D2513-06A Revision
March 1, 2006 D2513-06 Revision
Nov. 16, 2005 D2513-05 Revision
June 1, 2004 D2513-04A Revision
Jan. 1, 2004 D2513-04 Revision
Sept. 10, 2003 D2513-03B Revision
May 10, 2003 D2513-03A Revision
Jan. 10, 2003 D2513-03 Revision
Aug. 10, 2001 D2513-01AE01 Revision
Aug. 10, 2001 D2513-01A Revision
Aug. 10, 2001 D2513-01 Revision
Aug. 10, 2001 D2513-00 Revision
May 10, 1999 D2513-99 Revision
Not Available D2513-87 Revision