Logo

ASTM D228-08

Current Revision

Standard Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing and Waterproofing

$91.00

$91.00

$163.80

$0.00

$0.00

$0.00



Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


Stay effortlessly up-to-date with the latest standard revisions. When new versions are released, they're automatically charged and delivered to you, ensuring seamless compliance.

...

1.1 These test methods cover procedures for sampling, examination, physical testing, and analyses of asphalt-containing materials used in roofing and waterproofing. These materials include but are not limited to roll roofing, cap sheets, and shingles. Any of these materials are allowed to be partially or fully coated, surfaced, or laminated, or a combination thereof.

1.2 The test methods and procedures in this standard appear in the following order:

SectionContent
5Types of Roofing
6Sampling
7Mass and Area Determination
8Selection of Representative Specimens
9Moisture
10Pliability
11Mass Loss and Behavior on Heating
12Tear Strength
13Fastener Pull-Through Resistance
14Preparation and Selection of Small Test Specimens
for Analyses
15Analysis of Glass Felt Products
16Analysis of Roofing Products with Organic Felts
17Ash of Desaturated Felt
18Calculation
19Adjusting Back Coating Fine Mineral Matter and
Back Surfacing
20Report
21Precision and Bias

1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

These test methods include procedures for sampling, examination, physical testing, and analyses of asphalt roll roofing, cap sheets, and shingles used in roofing and waterproofing. Other components of these materials are allowed to include, but are not limited to, felts, mats, films, foils, mineral stabilizers, papers, and mineral surfacing.

These test methods include tests that are not required by every product standard that references Test Methods D 228. The individual product standards are the authority for which tests are required for compliance. It is not prohibited to run tests in addition to those required in the product standards, but these test methods make no claim to their suitability or significance.

Five random samples are required from lots equal to or less than 1000 packages. The number of samples required for lots greater than 1000 packages is dependent on the variation in the unit mass within the lot and is determined by the two-step sampling plan in 6.4.

The results of a visual examination, physical testing, and compositional analysis are required for each sample. The analytical data are further used to compute the probable minimum and the probable range for the average mass of each of the components.

SDO ASTM: ASTM International
Document Number D228
Publication Date Sept. 15, 2008
Language en - English
Page Count 13
Revision Level 08
Supercedes
Committee D08.02
Publish Date Document Id Type View
Sept. 15, 2008 D0228-08 Revision
May 1, 2006 D0228-06 Revision
Nov. 1, 2005 D0228-05B Revision
July 15, 2005 D0228-05A Revision
March 1, 2005 D0228-05 Revision
July 1, 2004 D0228-04 Revision
Dec. 1, 2003 D0228-03A Revision
July 10, 2003 D0228-03 Revision
July 10, 2002 D0228-02 Revision
Aug. 10, 2001 D0228-01 Revision
Aug. 10, 2001 D0228-00B Revision