Logo

ASTM C833-23

Current Revision

Standard Specification for Sintered (Uranium-Plutonium) Dioxide Pellets for Light Water Reactors

$69.00

$69.00

$124.20

$83.00

$83.00

$149.40



Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


Stay effortlessly up-to-date with the latest standard revisions. When new versions are released, they're automatically charged and delivered to you, ensuring seamless compliance.

...

1.1 This specification covers finished sintered and ground (U, Pu)O2 pellets for use in light water reactors. It applies to (U, Pu)O2 pellets containing a plutonium mass fraction up to 15 % (that is, mass of Pu divided by the sum of masses U, Pu, and Am yielding 0.15 or less).

1.2 Pellets produced under this specification are available in four grades.

1.2.1 Grade R—240Pu / (Pu + Am) isotope mass fraction is at least 19 %.

1.2.2 Grade F—240Pu / (Pu + Am) isotope mass fraction is at least 7 % and less than 19 %.

1.2.3 Grade N1—240Pu / (Pu + Am) isotope mass fraction is less than 7 %.

1.2.4 Grade N2—240Pu /239Pu isotope mass fraction does not exceed 0.10 (10 %).

1.3 There is no discussion of or provision for preventing criticality incidents, nor are health and safety requirements, the avoidance of hazards, or shipping precautions and controls discussed. Observance of this specification does not relieve the user of the obligation to be aware of and conform to all applicable international, federal, state, and local regulations pertaining to possessing, processing, shipping, or using source or special nuclear material. Examples of U.S. government documents are Code of Federal Regulations Title 10, Part 50—Domestic Licensing of Production and Utilization Facilities; Code of Federal Regulations Title 10, Part 71—Packaging and Transportation of Radioactive Material; and Code of Federal Regulations Title 49, Part 173—General Requirements for Shipments and Packaging.

1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5 The following safety hazards caveat pertains only to the technical requirements portion, Section 4, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


This specification covers finished sintered and ground (uranium-plutonium) dioxide pellets for use in thermal reactors. It applies to uranium-plutonium dioxide pellets containing plutonium additions up to 15 % weight. The diversity of manufacturing methods shall be recognized by which uranium-plutonium dioxide pellets are produced and the many special requirements for chemical and physical characterization that may be imposed by the operating conditions to which the pellets will be subjected in specific reactor systems. The following are different chemical requirements that shall be determined: uranium content, plutonium content, impurity content, stoichiometry, moisture content, gas content, and americium-241 content. Nuclear requirements such as isotopic content, plutonium equivalent at a given date, equivalent boron content, and reactivity shall also be determined. Physical properties of the pellets like dimensions, density, grain size, pore morphology, plutonium-oxide homogeneity, plutonium-oxide particle size, plutonium-oxide particle distribution, integrity, and surface cracks shall be determined as well. The surfaces of finished pellets shall be visually free of loose chips, oil, macroscopic inclusions, and foreign materials. An estimate of the fuel pellet irradiation stability shall be obtained unless adequate allowance for such effects are factored into the fuel rod design. The estimate of the stability shall consist of either conformance to the thermal stability test as specified in the or by adequate correlation of manufacturing process or microstructure to in-reactor behavior, or both.


SDO ASTM: ASTM International
Document Number C833
Publication Date June 1, 2023
Language en - English
Page Count 5
Revision Level 23
Supercedes
Committee C26.02
Publish Date Document Id Type View
June 1, 2023 C0833-23 Revision
Jan. 1, 2017 C0833-17 Revision
Jan. 1, 2013 C0833-13 Revision
June 10, 2001 C0833-95A Revision
June 10, 2001 C0833-01 Revision
Dec. 1, 2008 C0833-01R08 Reaffirmation