Logo

ASTM B860-09a

Historical Revision

Standard Specification for Zinc Master Alloys for Use in Hot Dip Galvanizing

$73.00

$73.00

$131.40


Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


Stay effortlessly up-to-date with the latest standard revisions. When new versions are released, they're automatically charged and delivered to you, ensuring seamless compliance.

...

1.1 This specification covers zinc master alloys which are used in hot dip galvanizing for the purpose of adjusting the concentration of certain alloying elements in the molten zinc bath. Table 1 covers the chemical composition of these materials which include six master alloys of zinc-aluminum (brightener) and one master alloy of zinc-antimony.

ASTM Common UNS
Type A-190/10 Zn/Al High PurityZ30750
Type A-290/10 Zn/Al Low PurityZ31710
Type A-395/5 Zn/Al High PurityZ30503
Type A-495/5 Zn/Al Low PurityZ31510
Type A-596/4 Zn/Al High Purity...
Type A-696/4 Zn/AlLow Purity...
Type S-190/10 Zn/Sb Z55710

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

TABLE 1 Chemical Requirements Composition, % (Range or Maximum Value)A

Type A-190 % Zinc10 % Aluminum (90/10 Zn/Al)High Purity
Type A-290 % Zinc10 % Aluminum (90/10 Zn/Al)Low Purity
Type A-395 % Zinc5 % Aluminum (95/5 Zn/Al)High Purity
Type A-495 % Zinc5 % Aluminum (95/5 Zn/Al)Low Purity
Type A-596 % Zinc4 % Aluminum (96/4 Zn/Al)High Purity
Type A-696 % Zinc4 % Aluminum (96/4 Zn/Al)Low Purity
Type S-190 % Zinc10 % Antimony (90/10 Zn/Sb)
UNSBType A-1
90/10 Zn/Al
Z30750
Type A-2
90/10 Zn/Al
Z31710
Type A-3
95/5 Zn/Al
Z30503
Type A-4
95/5 Zn/Al
Z31510
Type A-5
96/4 Zn/Al
ZXXXXX
Type A-6
96/4 Zn/Al
ZXXXXX
Type S-1
90/10 Zn/Sb
Z55710
Fe0.05 max0.15 max0.05 max0.15 max0.05 max0.15 max0.03 max
Pb0.005 max0.4 max0.005 max0.4 max0.0005 max0.4 max0.015 max
Cd0.004 max...0.004 max...0.004 max...0.003 max
Cu0.035 max0.5 max0.035 max0.5 max0.035 max0.5 max0.003 max
Mg............0.06 max0.06 max
Sn0.003 max...0.003 max...0.003 max...0.01 max
As..................0.015 max
Al9.510.59.510.54.55.54.55.54.0-4.54.0-4.5...
SbC..................9.510.5
Others, Total0.01 max0.25 max0.01 max0.25 max0.01 max0.25 max0.03 max
ZnDRemainderRemainderRemainderRemainderRemainderRemainderRemainder

A The following applies to all specified limits in this table: For purposes of determining conformance with this specification, an observed value obtained from analysis shall be rounded off to the nearest unit in the last right-hand place of figures used in expressing the limiting value, in accordance with the rounding method of Practice E29.

B UNS numbers in conformance with Practice E527.

C Chemical method under development.

D For information only. Quantitative determination of this element is not required. Zinc is assumed to be the difference between 100 % and the sum of those elements listed above.


This specification covers zinc master alloys which are used in hot dip galvanizing for the purpose of adjusting the concentration of certain alloying elements in the molten zinc bath. The paper presented the chemical composition of these materials which include six master alloys of zinc aluminium; Type A-1, Type A-2, Type A-3, Type A-4, Type A-5, Type A-6, and one master alloy of zinc-antimony, Type S-1. The material covered by this specification shall be made of uniform quality and shall be free from harmful contamination. The alloys shall be tested and conform to the required chemical composition requirements.


SDO ASTM: ASTM International
Document Number B860
Publication Date Oct. 1, 2009
Language en - English
Page Count 3
Revision Level 09a
Supercedes
Committee B02.04
Publish Date Document Id Type View
Nov. 1, 2018 B0860-18 Revision
June 1, 2017 B0860-17 Revision
May 1, 2016 B0860-16 Revision
Oct. 1, 2015 B0860-15 Revision
Feb. 1, 2013 B0860-13 Revision
Oct. 1, 2009 B0860-09AE01 Revision
Oct. 1, 2009 B0860-09A Revision
April 15, 2009 B0860-09 Revision
Nov. 1, 2008 B0860-08 Revision
June 1, 2007 B0860-07 Revision
May 10, 2002 B0860-05 Revision
May 10, 2002 B0860-02 Revision
May 10, 2002 B0860-01E01 Revision
May 10, 2002 B0860-01 Revision
May 10, 2002 B0860-00 Revision
Oct. 1, 2022 B0860-18R22 Reaffirmation