Logo

ASTM B250/B250M-19

Current Revision

Standard Specification for General Requirements for Wrought Copper Alloy Wire

$69.00

$69.00

$124.20

$83.00

$83.00

$149.40



Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


Stay effortlessly up-to-date with the latest standard revisions. When new versions are released, they're automatically charged and delivered to you, ensuring seamless compliance.

...

1.1 This specification establishes requirements common to wrought copper and copper alloy wire and shall apply to Specifications B16/B16M, B99/B99M, B134/B134M, B159/B159M, B197/B197M, B206/B206M, B272, B301/B301M, B453/B453M, B967/B967M, B974/B974M, and B981/B981M to the extent referenced therein.

1.2 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification shall be prescribed in the product specification.

1.3 Units—Values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other and values from the two systems shall not be combined.

1.4 The following safety hazard caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and to determine the applicability of regulatory limitations prior to use.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


This specification establishes the general requirements common to wrought copper and copper alloy wires. The materials for manufacture shall be a cast bar, billet, rod, or other form of such purity and soundness as to be suitable for processing by hot working, cold working, and subsequent annealing to produce finished products that meet the specified temper properties and have a uniform wrought structure. Products shall be sampled and prepared, then tested accordingly to examine their conformance to dimensional (diameter, thickness, specific and stock lengths, width, straightness, and edge contour), mechanical (tensile, yield and bend strengths, elongation, and Rockwell hardness), electrical (resistivity and conductivity), chemical composition, and grain size requirements. In the event of conflict between this specification and the individual casting product specifications, the requirements of the casting specification shall take precedence.


12.1 For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.

Property

Rounded Unit for Observed
or Calculated Value

 

 

  Dimensions
  Chemical composition
  Hardness
  Electrical resistivity/conductivity

  nearest unit in the last
   right-hand significant
   digit used in expressing
   the limiting value

 

  Tensile strength
  Yield strength

  nearest ksi [5 MPa]
  

 

  Elongation

 

   Below 5 %

  nearest multiple of 0.5 %

   5 % and over

  nearest 1 %

 

  Grain size

 

   Under 0.060 mm

  nearest multiple of 0.005 mm

   0.060 mm and over

  nearest 0.01 mm

SDO ASTM: ASTM International
Document Number B250
Publication Date Oct. 1, 2019
Language en - English
Page Count 10
Revision Level 19
Supercedes
Committee B05.02
Publish Date Document Id Type View
Oct. 1, 2019 B0250_B0250M-19 Revision
Oct. 1, 2016 B0250_B0250M-16 Revision
April 1, 2013 B0250_B0250M-13 Revision
Oct. 1, 2012 B0250_B0250M-12 Revision
Oct. 1, 2007 B0250_B0250M-07 Revision
Nov. 10, 2001 B0250_B0250M-01E01 Revision
Nov. 10, 2001 B0250_B0250M-01 Revision