Logo

ASTM B240-17

Historical Revision

Standard Specification for Zinc and Zinc-Aluminum (ZA) Alloys in Ingot Form for Foundry and Die Castings

$73.00

$73.00

$131.40


Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


Stay effortlessly up-to-date with the latest standard revisions. When new versions are released, they're automatically charged and delivered to you, ensuring seamless compliance.

...

1.1 This specification covers commercial zinc and zinc-aluminum (ZA) alloys in ingot form for remelting for the manufacture of pressure die castings, foundry castings and continuous cast bar stock as designated and specified in Table 1. Seven alloy compositions are specified, designated as follows:

Common

Traditional

ASTMA

UNSA

 

 

 

 

Alloy 3

Zamak 3

AG 40A

Z33524

Alloy 7

Zamak 7

AG 40B

Z33526

Alloy 5

Zamak 5

AC 41A

Z35532

Alloy 2

Zamak 2

AC 43A

Z35544

ZA-8

ZA-8 

...

Z35637

ZA-12

ZA-12

...

Z35632

ZA-27

ZA-27

...

Z35842

ACuZinc52

ACuZinc5

...

Z46540

(A) See Table 1, footnote B.
(A) Zinc alloy ingot for die casting may contain nickel, chromium, silicon, and manganese in amounts of up to 0.02, 0.02, 0.035 and 0.05 %, respectively. No harmful effects have ever been noted due to the presence of these elements in up to these concentrations and, therefore, analyses are not required for these elements, except that nickel analysis is required for Z33526.
(B) ASTM alloy designations were established in accordance with Practice B275. UNS assignations were established in accordance with Practice E527. The last digit of a UNS number differentiates between alloys of similar composition. UNS designations for ingot and casting versions of an alloy were not assigned in the same sequence for all alloys.
(C) For purposes of acceptance and rejection, the observed value or calculated value obtained from analysis should be rounded to the nearest unit in the last right-hand place of figures, used in expressing the specified limit, in accordance with the rounding procedure prescribed in Practice E29.
(D) When this material is required to conform to ISO Standard 301, the chemical limits for thallium and indium each shall not exceed 0.001 %.
(E) Zinc-aluminum ingot for foundry and pressure die casting may contain nickel, chromium, and manganese in amounts of up to 0.01 % each or 0.03 % total. No harmful effects have ever been noted due to the presence of these elements in up to these concentrations and, therefore, analyses are not required for these elements.
(F) Refer to Practice B908. (Note: Colors indicated are for North American applications.)
(G) Determined arithmetically by difference.

1.2 Zinc alloys Z33524, Z33526, Z35532, Z46540, and Z35544 are used primarily for remelting in the manufacture of pressure die castings. Zinc-aluminum alloys Z35637, Z35632, and Z35842 are used for remelting in the manufacture of both foundry and pressure die castings. Castings made from these ingots are specified in Specification B86, Standard Specification for Zinc and Zinc-Aluminum Alloys for Foundry and Die Castings.

1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

1.4 Systems of nomenclature used to designate zinc and zinc-aluminum (ZA) alloys used for casting are described in Appendix X1.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.

1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


This specification covers commercial zinc and zinc-aluminum alloys in ingot form for remelting for the manufacture of pressure die castings, foundry castings and continuous cast bar stock. Seven alloy compositions are specified, which includes Z33521, Z33522, Z35530, Z35540, for zinc alloys and Z35635, Z35630, Z35840, for zinc-aluminum alloys. The material shall be of uniform quality and reasonably free from dross, adhering foreign matter, and surafce oxide. The determination of chemical composition shall be made in accordance with suitable analytical methods.


SDO ASTM: ASTM International
Document Number B240
Publication Date Nov. 1, 2017
Language en - English
Page Count 4
Revision Level 17
Supercedes
Committee B02.04
Publish Date Document Id Type View
April 1, 2022 B0240-22 Revision
Nov. 1, 2021 B0240-21 Revision
Nov. 1, 2017 B0240-17 Revision
Feb. 1, 2013 B0240-13 Revision
April 1, 2010 B0240-10 Revision
Oct. 1, 2009 B0240-09 Revision
July 1, 2007 B0240-07E01 Revision
July 1, 2007 B0240-07 Revision
Aug. 1, 2006 B0240-06 Revision
Nov. 1, 2005 B0240-05 Revision
Oct. 1, 2004 B0240-04E01 Revision
Oct. 1, 2004 B0240-04 Revision
June 10, 2003 B0240-03 Revision
May 10, 2001 B0240-98E01 Revision
May 10, 2001 B0240-01E01 Revision
May 10, 2001 B0240-01 Revision