1.1 This specification covers structural quality alloy steel plates.
1.2 The plates are usually specified to chemical composition requirements, but tensile properties may also be specified.
1.2.1 When tensile properties are required, the specific requirements must be compatible with the chemical composition, condition, and plate thickness.
1.3 The plates are available in the following four conditions:
1.3.1 Condition AR—As rolled (hot rolled),
1.3.2 Condition A—Annealed,
1.3.3 Condition N—Normalized, and
1.3.4 Condition NT—Normalized and tempered.
1.4 The plates are available in the following three forms:
1.4.1 Form I—Rectangular,
1.4.2 Form II—Circular and semi-circular, and
1.4.3 Form III—Sketch, including rings.
1.5 The plates are available in the following five edge categories:
1.5.1 Edge 1—Mill edge,
1.5.2 Edge 2—Universal mill edge,
1.5.3 Edge 3—Sheared edge,
1.5.4 Edge 4—Gas cut edge, and
1.5.5 Edge 5—Special cut edge.
1.6 The plates are available in the following seven finishes:
1.6.1 Finish 1—As rolled (hot rolled),
1.6.2 Finish 2—Blast cleaned,
1.6.3 Finish 3—Blast cleaned and oiled,
1.6.4 Finish 4—Pickled,
1.6.5 Finish 5—Pickled and oiled,
1.6.6 Finish 6—Painted, one prime coat, and
1.6.7 Finish 7—Painted, one prime coat and one finish coat.
1.6.8 The plates are usually specified to have Finish 1.
1.7 Supplementary requirements are provided for additional requirements that may be specified on the order.
1.8 When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. See Appendix X3 of Specification A6/A6M for information on weldability.
1.9 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
This specification deals with alloy structural steel plates. Plate specimens addressed under this specification are available in four treatment conditions (as rolled or hot rolled; annealed; normalized; and normalized and tempered), three structural forms (rectangular; circular and semi-circular; and sketch, including rings), five edge categories (mill edge; universal mill edge; sheared edge; gas cut edge; and special cut edge), and seven finishes (as rolled or hot rolled; blast cleaned; blast cleaned and oiled; pickled; pickled and oiled; painted with one prime coat; and painted with one prime coat and one finish coat). Steel materials shall be manufactured and furnished in defined procedures unless specified otherwise in the purchase order. Heat analysis shall be performed wherein steel specimens shall conform to required chemical compositions of carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, vanadium, and copper. Specimens shall also undergo tensile tests and shall conform to required values of tensile strength.
SDO | ASTM: ASTM International |
Document Number | A829 |
Publication Date | May 1, 2014 |
Language | en - English |
Page Count | 4 |
Revision Level | 14 |
Supercedes | |
Committee | A01.02 |
Please enter your email address to continue ...
Have an account?
IMPORTANT - READ CAREFULLY BEFORE DOWNLOADING OR COPYING TO YOUR COMPUTER ANY FILE(S) CONTAINED HEREWITH.
BY ACCESSING THE PRODUCT, YOU ACKNOWLEDGE THAT YOU HAVE READ THE TERMS OF THIS LICENSE AGREEMENT AND AGREE TO BE BOUND BY ITS TERMS.
We're glad to see you again! Please enter your email and password to continue
Need an account?
Register for an account to join our community! Gain access to exclusive content, participate in discussions, and stay updated on the latest news.
Have an account?
Forgot your password? No worries! Please enter your email to reset your password. If your email exists in our system, you will receive a password reset link.
Have an account?
We've sent an email to reset your password if an account with that email exists. Please check your inbox and follow the instructions in the email. If you don't see the email, please check your spam folder.
Please read these terms of service ("terms", "terms of service") carefully before using Document-Center/Nimonik website (the "service") operated by Nimonik ("us", 'we", "our").
We will provide their services to you, which are subject to the conditions stated below in this document. Every time you visit this website, use its services or make a purchase, you accept the following conditions. This is why we urge you to read them carefully.
Before you continue using our website we advise you to read our Privacy Policy regarding our user data collection. It will help you better understand our practices.
Content published on this website (digital downloads, images, texts, graphics, logos) is the property of Nimonik and/or its respective licensors and protected by international copyright laws. The entire compilation of the content found on this website is the exclusive property of Nimonik and its respective licensors, with copyright authorship for this compilation by Nimonik and its respective licensors.
The entire communication with us is electronic. Every time you send us an email or visit our website, you are going to be communicating with us. You hereby consent to receive communications from us. If you subscribe to the news on our website, you are going to receive regular emails from us. We will continue to communicate with you by posting news and notices on our website and by sending you emails. You also agree that all notices, disclosures, agreements and other communications we provide to you electronically meet the legal requirements that such communications be in writing.
This privacy policy will explain how our organization uses the personal data we collect from you when you use our website.
Topics:
Our Company collects the following data:
Your data protection rights:
We have sent a verification email to you. Please check your inbox and follow the instructions in the email to verify your account. If you don't see the email, please check your spam folder.
We use cookies to enhance your browsing experience and analyze our traffic. By clicking "Accept All", you consent to our use of cookies.
These cookies are always on, as they're essential for making this website work, and making it safe. Without these cookies, services you've asked for can't be provided.
Remembers your cookie preferences and consent choices. Required for GDPR compliance. Duration: 1 year. Purpose: Legal Compliance
Protects against Cross-Site Request Forgery attacks. Required for form submissions and security. Duration: Session (expires when browser closes). Purpose: Security
Maintains your login session and authentication state. Essential for security and user experience. Duration: Session (expires when browser closes). Purpose: Authentication
These cookies help us analyse how many people are using this website, where they come from and how they're using it. If you opt out of these cookies, we can't get feedback to make this website better for you and all our users.
Google Analytics 4 cookie that maintains session state and tracks page views within a session. Duration: 2 years. Purpose: Website Analytics
Domain: localhostGoogle Analytics cookie that distinguishes unique users by assigning a randomly generated number as a client identifier. Duration: 2 years. Purpose: Website Analytics
Domain: localhostWe're glad to see you have made it to our new platform (formerly document-center.com).
As we finalize the transition to our new store, we will be migrating accounts from document-center.com.
Please keep an eye on your inbox for an email from us (standards@nimonik.com) as we will notify you when the account migration has succesfully completed.
For any questions or assistance, visit our Support Portal or email us at standards@nimonik.com