1.1 This specification covers carbon steel flat wire in coils or cut lengths. Flat wire is classified as a cold-rolled section, rectangular in shape, 0.500 in. [12.7 mm] or less in width and under 0.250 in. [6.35 mm] in thickness.
1.2 Low-carbon steel flat wire is produced from steel compositions with a maximum carbon content of 0.25 % by cast or heat analysis.
1.3 Carbon spring steel flat wire is produced to a carbon range in which the specified or required maximum is over 0.25 % by cast or heat analysis.
1.3.1 Two types of carbon spring steel flat wire are produced:
1.3.1.1 Untempered cold-rolled carbon spring steel flat wire, produced to several desirable combinations of properties and
1.3.1.2 Hardened and tempered carbon spring steel wire.
1.4 Definite application flat wire is a product developed for a specific application and may be specified only by size and descriptive name.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are for information only.
This specification covers carbon steel flat wire in coils or cut lengths. The steel materials shall be produced from rimmed, capped, semi-killed, hot-rolled or cold-rolled steel. The steel specimens shall undergo cast or heat analysis and product analysis and shall conform to the required chemical compositions of carbon, manganese, phosphorus, sulfur, silicon, and copper. The desired edge shall be classified as follows: prepared edge of a specified contour produced when a very accurate width is required or when the finish of the edge suitable for electroplating is required, or both (Number 1 Edge); not applicable to flat wire products ( Number 2 Edge); approximately square edge produced by slitting (Number 3 Edge); rounded edge produced either by edge rolling or resulting from flat rolling of a round section (Number 4 Edge); square edge produced from slit-edge material on which the burr is eliminated by rolling or filling (Number 5 Edge); and square edge produced by edge rolling when the width tolerance and edge condition are not as exacting as for No. 1 Edge (Number 6 Edge). The dimensional tolerances shall conform to the required values of thickness, width and length. The steel materials shall conform to the required values of temper, Rockwell hardness and tensile strength.
SDO | ASTM: ASTM International |
Document Number | A805 |
Publication Date | March 1, 2008 |
Language | en - English |
Page Count | 11 |
Revision Level | 08 |
Supercedes | |
Committee | A01.19 |
Please enter your email address to continue ...
Have an account?
IMPORTANT - READ CAREFULLY BEFORE DOWNLOADING OR COPYING TO YOUR COMPUTER ANY FILE(S) CONTAINED HEREWITH.
BY ACCESSING THE PRODUCT, YOU ACKNOWLEDGE THAT YOU HAVE READ THE TERMS OF THIS LICENSE AGREEMENT AND AGREE TO BE BOUND BY ITS TERMS.
We're glad to see you again! Please enter your email and password to continue
Need an account?
Register for an account to join our community! Gain access to exclusive content, participate in discussions, and stay updated on the latest news.
Have an account?
Forgot your password? No worries! Please enter your email to reset your password. If your email exists in our system, you will receive a password reset link.
Have an account?
We've sent an email to reset your password if an account with that email exists. Please check your inbox and follow the instructions in the email. If you don't see the email, please check your spam folder.
Please read these terms of service ("terms", "terms of service") carefully before using Document-Center/Nimonik website (the "service") operated by Nimonik ("us", 'we", "our").
We will provide their services to you, which are subject to the conditions stated below in this document. Every time you visit this website, use its services or make a purchase, you accept the following conditions. This is why we urge you to read them carefully.
Before you continue using our website we advise you to read our Privacy Policy regarding our user data collection. It will help you better understand our practices.
Content published on this website (digital downloads, images, texts, graphics, logos) is the property of Nimonik and/or its respective licensors and protected by international copyright laws. The entire compilation of the content found on this website is the exclusive property of Nimonik and its respective licensors, with copyright authorship for this compilation by Nimonik and its respective licensors.
The entire communication with us is electronic. Every time you send us an email or visit our website, you are going to be communicating with us. You hereby consent to receive communications from us. If you subscribe to the news on our website, you are going to receive regular emails from us. We will continue to communicate with you by posting news and notices on our website and by sending you emails. You also agree that all notices, disclosures, agreements and other communications we provide to you electronically meet the legal requirements that such communications be in writing.
This privacy policy will explain how our organization uses the personal data we collect from you when you use our website.
Topics:
Our Company collects the following data:
Your data protection rights:
We have sent a verification email to you. Please check your inbox and follow the instructions in the email to verify your account. If you don't see the email, please check your spam folder.