Logo

ASTM A710/A710M-19

Current Revision

Standard Specification for Precipitation-Strengthened Low-Carbon Nickel-Copper-Chromium-Molybdenum-Columbium Alloy Structural Steel Plates

$61.00

$61.00

$109.80

$73.00

$73.00

$131.40



Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


Stay effortlessly up-to-date with the latest standard revisions. When new versions are released, they're automatically charged and delivered to you, ensuring seamless compliance.

...

1.1 This specification covers low-carbon precipitation — strengthened nickel - copper - chromium - molybdenum - columbium (niobium) alloy steel plates for general applications. The alloys in this specification are strengthened by precipitation in various temperature ranges. Precipitation strengthening can occur upon air cooling after hot rolling, during normalizing, and by another heat treatment. These grades are not intended for use in applications above 900°F [480°C].

1.2 Two grades, each with three classes, are provided as follows:

Grade and Class

Condition

 

 

  Grade A, Class 1

as-rolled and precipitation heat treated

  Grade A, Class 2

normalized and precipitation heat treated

  Grade A, Class 3

quenched and precipitation heat treated

  Grade B, Class 1

as-rolled

  Grade B, Class 2

normalized

  Grade B, Class 3

normalized and precipitation heat treated

1.3 Grade A provides minimum yield strength levels ranging from 50 to 85 ksi [345 to 585 MPa], depending on thickness and condition.

1.4 Grade A, Class 1, plates are limited to a maximum thickness of 3/4 in. [20 mm]. The maximum thickness of Grade A, Classes 2 and 3, is limited only by the capacity of the composition to meet the specified mechanical property requirements; however, current practice normally limits the maximum thickness to 8 in. [200 mm].

1.5 Mandatory notch toughness requirements are specified for Grade A, Class 1.

1.6 Grade B provides minimum yield strength levels ranging from 70 to 75 ksi [485 to 515 MPa], depending on thickness and condition.

1.7 Grade B plates are limited to a maximum thickness of 2 in. [50 mm].

1.8 Mandatory notch toughness requirements are specified for the three classes of Grade B.

1.9 When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. See Appendix X3 of Specification A6/A6M for information on weldability.

1.10 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


This specification covers precipitation-strengthened low carbon nickel copper-chromium-molybdenum-columbium alloy structural steel plates. Precipitation strengthening and precipitation heat treatment shall be performed on the material to enhance and alter the required structural and mechanical properties. Heat analysis shall be used to determine the required chemical composition for carbon, manganese, phosphorus, sulfur, nickel, chromium, molybdenum, copper, columbium, and titanium. Yield strength, tensile strength, and elongation shall be evaluated using tension test and the required toughness shall be evaluated using notch toughness test.


SDO ASTM: ASTM International
Document Number A710
Publication Date Nov. 1, 2019
Language en - English
Page Count 4
Revision Level 19
Supercedes
Committee A01.02
Publish Date Document Id Type View
Nov. 1, 2019 A0710_A0710M-19 Revision
Sept. 10, 2002 A0710_A0710M-02 Revision
Sept. 10, 2001 A0710_A0710M-01 Revision
Sept. 10, 2001 A0710_A0710M-00 Revision
May 15, 2013 A0710_A0710M-02R13 Reaffirmation
March 1, 2007 A0710_A0710M-02R07 Reaffirmation