Logo

ASTM A706/A706M-00

Historical Revision

Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement

$83.00

$83.00

$149.40


Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


Stay effortlessly up-to-date with the latest standard revisions. When new versions are released, they're automatically charged and delivered to you, ensuring seamless compliance.

...

1.1 General--This specification covers deformed and plain low-alloy steel bars in cut lengths or coils for concrete reinforcement intended for applications where restrictive mechanical properties and chemical composition are required for compatibility with controlled tensile property applications or to enhance weldability. The standard sizes and dimensions of deformed bars and their number designations are given in Table 1 . The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this specification.

1.2 Grade--Bars are of a single minimum yield strength level: namely, 60 000 psi [420 MPa], designated as Grade 60 [420].

1.3 Plain rounds, in sizes up to and including 2 in. [50.8 mm] in diameter in coils or cut lengths, when ordered, shall be furnished under this specification. For ductility properties (elongation and bending), test provisions of the nearest smaller nominal diameter deformed bar size shall apply.

1.4 Controlled Tensile Properties--This specification limits mechanical properties (Table 2) to provide the desired yield/tensile properties for controlled tensile property applications.

1.5 Welding--This specification limits chemical composition (6.2) and carbon equivalent (6.4) to enhance the weldability of the material. When steel is to be welded, a welding procedure suitable for the chemical composition and intended use or service should be used. The use of the latest edition of ANSI/AWS D1.4 is recommended. This document describes the proper selection of the filler metals, preheat/interpass temperatures, as well as, performance and procedure qualification requirements.

1.6 This specification is applicable for orders in either inch-pound units (Specification A706) or in SI units [Specification A706M].

1.7 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.


SDO ASTM: ASTM International
Document Number A706
Publication Date March 10, 2001
Language en - English
Page Count 5
Revision Level 00
Supercedes
Committee A01.05
Publish Date Document Id Type View
May 15, 2024 A0706_A0706M-24 Revision
Dec. 1, 2022 A0706_A0706M-22A Revision
July 1, 2022 A0706_A0706M-22 Revision
Jan. 15, 2016 A0706_A0706M-16 Revision
July 1, 2015 A0706_A0706M-15 Revision
April 1, 2014 A0706_A0706M-14 Revision
Oct. 1, 2013 A0706_A0706M-13 Revision
Nov. 15, 2009 A0706_A0706M-09B Revision
Oct. 1, 2009 A0706_A0706M-09A Revision
May 1, 2009 A0706_A0706M-09 Revision
Oct. 1, 2008 A0706_A0706M-08A Revision
May 1, 2008 A0706_A0706M-08 Revision
May 1, 2006 A0706_A0706M-06A Revision
March 1, 2006 A0706_A0706M-06 Revision
July 1, 2005 A0706_A0706M-05A Revision
April 1, 2005 A0706_A0706M-05 Revision
Oct. 1, 2004 A0706_A0706M-04B Revision
May 1, 2004 A0706_A0706M-04A Revision
Jan. 1, 2004 A0706_A0706M-04 Revision
June 10, 2003 A0706_A0706M-03A Revision
April 10, 2003 A0706_A0706M-03 Revision
Dec. 10, 2002 A0706_A0706M-02 Revision
March 10, 2001 A0706_A0706M-01 Revision
March 10, 2001 A0706_A0706M-00 Revision