Logo

ASTM A653/A653M-09

Historical Revision

Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process

$91.00

$91.00

$163.80


Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


Stay effortlessly up-to-date with the latest standard revisions. When new versions are released, they're automatically charged and delivered to you, ensuring seamless compliance.

...

1.1 This specification covers steel sheet, zinc-coated (galvanized) or zinc-iron alloy-coated (galvannealed) by the hot-dip process in coils and cut lengths.

1.2 The product is produced in various zinc or zinc-iron alloy-coating weights [masses] or coating designations as shown in Table 1and in Table S2.1.

1.3 Product furnished under this specification shall conform to the applicable requirements of the latest issue of Specification A 924/A 924M, unless otherwise provided herein.

1.4 The product is available in a number of designations, grades and classes in four general categories that are designed to be compatible with different application requirements.

1.4.1 Steels with mandatory chemical requirements and typical mechanical properties.

1.4.2 Steels with mandatory chemical requirements and mandatory mechanical properties.

1.4.3 Steels with mandatory chemical requirements and mandatory mechanical properties that are achieved through solid-solution or bake hardening.

1.5 This specification is applicable to orders in either inch-pound units (as A 653) or SI units (as A 653M). Values in inch-pound and SI units are not necessarily equivalent. Within the text, SI units are shown in brackets. Each system shall be used independently of the other.

1.6 Unless the order specifies the M designation (SI units), the product shall be furnished to inch-pound units.

1.7 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this specification.

1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

TABLE 1 Weight [Mass] of Coating RequirementsA, B, C

Note— Use the information provided in 8.1.3 to obtain the approximate coating thickness from the coating weight [mass].

Minimum RequirementD
Triple-Spot Test
Single-Spot Test
Inch-Pound Units
TypeCoating DesignationTotal Both Sides, oz/ft2
One Side, oz/ft2
Total Both Sides, oz/ft2
ZincG01 no minimumno minimum no minimum
G30 0.300.100.25
G40 0.400.120.30
G60 0.600.200.50
G90 0.900.320.80
G1001.000.360.90
G1151.150.401.00
G1401.400.481.20
G1651.650.561.40
G1851.850.641.60
G2102.100.721.80
G2352.350.802.00
G3003.001.042.60
G3603.601.283.20
Zinc-iron alloyA01 no minimumno minimumno minimum
A25 0.250.080.20
A40 0.400.120.30
A60 0.600.200.50
SI Units
TypeCoating Designation
Total Both Sides, g/m2
One Side, g/m2
Total Both Sides, g/m2
ZincZ001 no minimumno minimumno minimum
Z90 90 30 75
Z120 120 36 90
Z180 180 60150
Z275 275 94235
Z305 305110275
Z350 350120300
Z450 450154385
Z500 500170425
Z550 550190475
Z600 600204510
Z700 700238595
Z900 900316790
Z11001100390975
Zinc-iron alloyZF001no minimumno minimumno minimum
ZF75 75 24 60
ZF120120 36 90
ZF180180 60150

A The coating designation is the term by which the minimum triple spot, total both sides coating weight [mass] is specified. Because of the many variables and changing conditions that are characteristic of continuous hot-dip coating lines, the zinc or zinc-iron alloy coating is not always evenly divided between the two surfaces of a coated sheet; nor is it always evenly distributed from edge to edge. However, the minimum triple-spot average coating weight (mass) on any one side shall not be less than 40 % of the single-spot requirement.

B As it is an established fact that the atmospheric corrosion resistance of zinc or zinc-iron alloy-coated sheet products is a direct function of coating thickness (weight (mass)), the selection of thinner (lighter) coating designations will result in almost linearly reduced corrosion performance of the coating. For example, heavier galvanized coatings perform adequately in bold atmospheric exposure whereas the lighter coatings are often further coated with paint or a similar barrier coating for increased corrosion resistance. Because of this relationship, products carrying the statement meets ASTM A 653/A 653M requirements should also specify the particular coating designation.

C International Standard, ISO 3575, continuous hot-dip zinc-coated carbon steel sheet contains Z100 and Z200 designations and does not specify a ZF75 coating.

D No minimum means that there are no established minimum requirements for triple- and single-spot tests.


This specification covers steel sheet, zinc-coated (galvanized) or zinc-iron alloy-coated (galvannealed) by the hot-dip process in coils and cut lengths. The material is available in several designations as follows: commercial steel, forming steel, deep drawing steel, extra deep drawing steel, structural steel, high strength low alloy steel, high strength low alloy steel with improved formability, solution hardened steel, and bake hardenable steel. Structural steel, high strength low alloy steel, solution hardened steel, and bake hardenable steel are available in several grades based on mechanical properties. Yield strength, elongation, and bending properties of the steel shall be determined. A bend test shall be done to the coated sheets.


SDO ASTM: ASTM International
Document Number A653
Publication Date May 1, 2009
Language en - English
Page Count 13
Revision Level 09
Supercedes
Committee A05.11
Publish Date Document Id Type View
May 1, 2023 A0653_A0653M-23 Revision
Nov. 1, 2022 A0653_A0653M-22 Revision
May 1, 2020 A0653_A0653M-20 Revision
Sept. 1, 2019 A0653_A0653M-19A Revision
July 1, 2019 A0653_A0653M-19 Revision
Nov. 1, 2018 A0653_A0653M-18 Revision
Nov. 1, 2017 A0653_A0653M-17 Revision
July 1, 2015 A0653_A0653M-15E01 Revision
July 1, 2015 A0653_A0653M-15 Revision
Dec. 1, 2013 A0653_A0653M-13 Revision
Nov. 1, 2011 A0653_A0653M-11 Revision
Nov. 1, 2010 A0653_A0653M-10 Revision
Dec. 1, 2009 A0653_A0653M-09A Revision
May 1, 2009 A0653_A0653M-09 Revision
July 15, 2008 A0653_A0653M-08 Revision
June 1, 2007 A0653_A0653M-07 Revision
Nov. 15, 2006 A0653_A0653M-06A Revision
May 1, 2006 A0653_A0653M-06 Revision
Oct. 1, 2005 A0653_A0653M-05A Revision
June 1, 2005 A0653_A0653M-05 Revision
May 1, 2004 A0653_A0653M-04A Revision
Feb. 1, 2004 A0653_A0653M-04 Revision
April 10, 2003 A0653_A0653M-03 Revision
Oct. 10, 2002 A0653_A0653M-02A Revision
June 10, 2002 A0653_A0653M-02 Revision
Oct. 10, 2001 A0653_A0653M-01A Revision
Oct. 10, 2001 A0653_A0653M-01 Revision
Oct. 10, 2001 A0653_A0653M-00 Revision
Not Available A0653_A0653M-98A Revision