Logo

ASTM A615/A615M-14

Historical Revision

Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement

$83.00

$83.00

$149.40

$0.00

$0.00

$0.00



Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


Stay effortlessly up-to-date with the latest standard revisions. When new versions are released, they're automatically charged and delivered to you, ensuring seamless compliance.

...

1.1 This specification covers deformed and plain carbon-steel bars in cut lengths and coils for concrete reinforcement. Steel bars containing alloy additions, such as with the Association for Iron and Steel Technology and the Society of Automotive Engineers series of alloy steels, are permitted if the resulting product meets all the other requirements of this specification. The standard sizes and dimensions of deformed bars and their number designations are given in Table 1.

1.2 Bars are of four minimum yield strength levels: namely, 40 000 psi [280 MPa], 60 000 psi [420 MPa], 75 000 psi [520 MPa], and 80 000 psi [550 MPa], designated as Grade 40 [280], Grade 60 [420], Grade 75 [520], and Grade 80 [550], respectively.

1.3 Plain bars, in sizes up to and including 21/2 in. [63.5 mm] in diameter in coils or cut lengths, when ordered shall be furnished under this specification in Grade 40 [280], Grade 60 [420], Grade 75 [520], and Grade 80 [550]. For ductility properties (elongation and bending), test provisions of the nearest smaller nominal diameter deformed bar size shall apply. Requirements providing for deformations and marking shall not be applicable.

Note 1Welding of the material in this specification should be approached with caution since no specific provisions have been included to enhance its weldability. When this steel is to be welded, a welding procedure suitable for the chemical composition and intended use or service should be used. The use of the latest edition of AWS D1.4/D1.4M is recommended. The AWS D1.4/D1.4M Welding Code describes the proper selection of the filler metals and preheat/interpass temperatures, as well as performance and procedure qualification requirements.

1.4 Requirements for alternate bar sizes are presented in Annex A1. The requirements in Annex A1 only apply when specified by the purchaser (see 4.2.4).

1.5 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables) shall not be considered as requirements of the specification.

1.6 This specification is applicable for orders in either inch-pound units (as Specification A615) or in SI units (as Specification A615M).

1.7 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the specification.

1.8 This specification does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this specification to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


This specification covers deformed and plain carbon-steel bars for concrete reinforcements in cut lengths and coils. Materials considered under this specification are available in Grades 40 [280], 60 [420] and 75 [520]. Steel samples shall be rolled from properly identified heats of mold cast or strand cast steel using electric-furnace, basic-oxygen, or open-hearth. Heat analysis shall be performed wherein steel materials shall conform to required compositions of carbon, manganese, phosphorus and sulfur. Steel specimens shall also undergo tensile tests and shall conform to required values of tensile strength, yield strength, and elongation. Steel samples shall also undergo deformation test, tension test and bend tests. Final products shall be marked by a tag.


SDO ASTM: ASTM International
Document Number A615
Publication Date April 1, 2014
Language en - English
Page Count 7
Revision Level 14
Supercedes
Committee A01.05
Publish Date Document Id Type View
May 15, 2024 A0615_A0615M-24 Revision
July 1, 2022 A0615_A0615M-22 Revision
April 1, 2020 A0615_A0615M-20 Revision
July 1, 2018 A0615_A0615M-18E01 Revision
July 1, 2018 A0615_A0615M-18 Revision
Jan. 15, 2016 A0615_A0615M-16 Revision
July 1, 2015 A0615_A0615M-15AE01 Revision
July 1, 2015 A0615_A0615M-15A Revision
April 1, 2015 A0615_A0615M-15 Revision
April 1, 2014 A0615_A0615M-14 Revision
Oct. 1, 2013 A0615_A0615M-13 Revision
March 1, 2012 A0615_A0615M-12 Revision
Nov. 15, 2009 A0615_A0615M-09B Revision
Oct. 1, 2009 A0615_A0615M-09A Revision
May 1, 2009 A0615_A0615M-09 Revision
Oct. 1, 2008 A0615_A0615M-08B Revision
May 1, 2008 A0615_A0615M-08A Revision
March 1, 2008 A0615_A0615M-08 Revision
March 1, 2007 A0615_A0615M-07 Revision
May 1, 2006 A0615_A0615M-06A Revision
March 1, 2006 A0615_A0615M-06 Revision
July 1, 2005 A0615_A0615M-05A Revision
April 1, 2005 A0615_A0615M-05 Revision
Oct. 1, 2004 A0615_A0615M-04B Revision
May 1, 2004 A0615_A0615M-04A Revision
Jan. 1, 2004 A0615_A0615M-04 Revision
June 10, 2003 A0615_A0615M-03A Revision
April 10, 2003 A0615_A0615M-03 Revision
Dec. 10, 2002 A0615_A0615M-02 Revision
Oct. 10, 2001 A0615_A0615M-01B Revision
Oct. 10, 2001 A0615_A0615M-01A Revision
Oct. 10, 2001 A0615_A0615M-01 Revision
Oct. 10, 2001 A0615_A0615M-00 Revision