Logo

ASTM A1098/A1098M-18

Current Revision

Standard Specification for Welded Austenitic, Ferritic, Martensitic and Duplex Stainless Steel Boiler, Superheater, Condenser, and Heat Exchanger Tubes with Textured Surface(s)

$91.00

$91.00

$163.80


Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


Stay effortlessly up-to-date with the latest standard revisions. When new versions are released, they're automatically charged and delivered to you, ensuring seamless compliance.

Document Preview Not Available...

1.1 This specification covers average or minimum-wall thickness welded tubes made from various grades of austenitic, ferritic, martensitic and duplex stainless steel materials in which the (1) external tube surface, (2) internal tube surface, or (3) both internal and external tube surfaces have a textured configuration for improved heat transfer or fluid flow or both. Texture surface(s) are produced by cold forming a specified configuration on the surface(s) of base strip material, prior to welding. The produced welded textured tubes may be used in boilers, superheaters, condensers, evaporators, heat exchangers, and other similar heat transfer apparatus in diameters up to and including 1.5 in. [38 mm] for various wall thicknesses up to and including 0.079 in. [2 mm].

1.2 The tubing sizes and thicknesses usually furnished to this specification are 0.375 in. [10 mm] inside diameter (ID) to 1.5 in. [38 mm] outside diameter and 0.020 to 0.079 in. [0.5 to 2 mm], inclusive, in wall thickness. Tubing having other dimensions may be furnished provided such tubes comply with all other requirements of this specification.

1.3 Optional supplementary requirements are provided and, when one or more of these are desired, each shall be so stated in the order.

1.4 Several grades of austenitic, ferritic, martensitic and duplex stainless steels are included in this specification. Not all alloys are suitable for all conditions. Selection will depend upon design and service requirements.

1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.

1.6 The following safety hazards statement pertains only to the test method and the Supplementary Requirements of this specification. A specific warning statement is given in the Supplementary Requirements. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


This specification applies to average or minimum-wall thickness welded tubes made from various grades of austenitic alloy steel materials in which the external tube surface, internal tube surface, or both internal and external tube surfaces have a textured configuration for improved heat transfer or fluid flow or both. Texture surface(s) are produced by cold forming a specified configuration on the surface(s) of base strip material, prior to welding. The produced welded textured tubes may be used in boilers, superheaters, condensers, evaporators, heat exchangers, and other similar heat transfer apparatus in diameters up to and including 1.5 in. [38 mm] for various wall thicknesses up to and including 0.079 in. [2 mm].

This specification includes requirements for manufacturing process, chemical composition, heat treatment, product analysis, tensile strength, hardness, reverse-bend test, workmanship, finish, and appearance. It also covers mechanical tests, nondestructive tests, forming operations, sampling, and product marking.


SDO ASTM: ASTM International
Document Number A1098
Publication Date Nov. 1, 2018
Language en - English
Page Count 11
Revision Level 18
Supercedes
Committee A01.10
Publish Date Document Id Type View
Nov. 1, 2018 A1098_A1098M-18 Revision
Nov. 15, 2016 A1098_A1098M-16 Revision
Sept. 1, 2022 A1098_A1098M-18R22 Reaffirmation