Logo

ASTM A1008/A1008M-09

Historical Revision

Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Required Hardness, Solution Hardened, and Bake Hardenable

$83.00

$83.00

$149.40


Sub Total (1 Item(s))

$ 0.00

Estimated Shipping

$ 0.00

Total (Pre-Tax)

$ 0.00


...

1.1 This specification covers cold-rolled, carbon, structural, high-strength low-alloy, high-strength low-alloy with improved formability, solution hardened, and bake hardenable steel sheet, in coils and cut lengths.

1.2 Cold rolled steel sheet is available in the designations as listed in 4.1.

1.3 This specification does not apply to steel strip as described in Specification A 109/A 109M.

1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.


This specification covers cold-rolled, carbon steel sheets, in coils and cut lengths, in the following designations: commercial steels (CS Types A, B, and C); drawing steel (DS Types A and B); deep drawing steel (DDS); extra deep drawing steel (EDDS); structural steel (SS Grades 25[170], 30[205], 33[230] Types 1 and 2, 40[275] Types 1 and 2, 50[340], 60[410], 70[480], and 80[550]); high-strength low-alloy steel (HSLAS Classes 1 and 2 of Grades 45[310], 50[340]. 55[380], 60[410], 65[450], and 70[480]), high-strength low-alloy steel with improved formability (HSLAS-F Grades 50[340], 60[410], 70[480], and 80[550]); solution hardened steel (SHS); and bake hardenable steel (BHS). Conformance of the steel sheets to chemical composition requirements shall be tested by heat analysis. Specimens shall also undergo tension and bending tests and shall conform to specified values of tensile and yield strength, elongation, and bake hardening index. Unless otherwise indicated, sheet surfaces shall have a matte finish and shall be oiled.


SDO ASTM: ASTM International
Document Number A1008
Publication Date May 1, 2009
Language en - English
Page Count 9
Revision Level 09
Supercedes
Committee A01.19
Publish Date Document Id Type View
May 1, 2024 A1008_A1008M-24 Revision
Nov. 1, 2023 A1008_A1008M-23E01 Revision
Nov. 1, 2023 A1008_A1008M-23 Revision
Nov. 1, 2021 A1008_A1008M-21A Revision
May 1, 2021 A1008_A1008M-21 Revision
July 1, 2020 A1008_A1008M-20 Revision
Sept. 1, 2018 A1008_A1008M-18 Revision
Sept. 1, 2016 A1008_A1008M-16 Revision
May 1, 2015 A1008_A1008M-15 Revision
Oct. 1, 2013 A1008_A1008M-13 Revision
Nov. 1, 2012 A1008_A1008M-12A Revision
March 1, 2012 A1008_A1008M-12 Revision
April 1, 2011 A1008_A1008M-11 Revision
April 1, 2010 A1008_A1008M-10 Revision
Nov. 1, 2009 A1008_A1008M-09A Revision
May 1, 2009 A1008_A1008M-09 Revision
Oct. 1, 2008 A1008_A1008M-08A Revision
July 1, 2008 A1008_A1008M-08 Revision
Sept. 1, 2007 A1008_A1008M-07A Revision
Feb. 1, 2007 A1008_A1008M-07 Revision
Oct. 1, 2006 A1008_A1008M-06A Revision
Sept. 1, 2006 A1008_A1008M-06 Revision
Dec. 1, 2005 A1008_A1008M-05B Revision
Sept. 15, 2005 A1008_A1008M-05A Revision
May 1, 2005 A1008_A1008M-05 Revision
July 1, 2004 A1008_A1008M-04B Revision
April 1, 2004 A1008_A1008M-04A Revision
Feb. 1, 2004 A1008_A1008M-04 Revision
April 10, 2003 A1008_A1008M-03 Revision
April 10, 2002 A1008_A1008M-02E01 Revision
April 10, 2002 A1008_A1008M-02 Revision
Sept. 10, 2001 A1008_A1008M-01A Revision
Jan. 10, 2001 A1008_A1008M-01E01 Revision
Aug. 10, 2000 A1008_A1008M-00 Revision